View AG-640480C2FTCW_4410544.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

AMP I RE
SPECIFICATIONS FOR LCD MODULE
CUSTOMER CUSTOMER PART NO. AMPIRE PART NO. APPROVED DATE BY AG-640480C2FTCW-02
APPROVED BY
CHECKED BY
ORGANIZED BY
Date : 2006/9/7
AMPIRE CO., LTD.
0
RECORD OF REVISION
Revision Date 2005/11/16 2006/9/7 3 Page New Release Modify General Specification Sunglin Contents Editor Sunglin
Date : 2006/9/7
AMPIRE CO., LTD.
1
1. GENERAL SPECIFICATIONS
Item Display Contents[pixels] Dimensional Outline[mm] Display mode Circuits Interface Contents 640(W)x480(H) 205.5(W)x141.0(H)x8.7 max(D) Transmissive Type (Viewing Direction 6 o'clock) X-Driver,Y-Driver Data(UD0~UD3,LD0~LD3),SCP,FP,LP,DISP
2.
ABSOLUTE MAXIMUM RATING
(1)ELECTRICAL ABSOLUTE RATINGS ITEM Input Voltage Static Electricity Note 1 SYMBOL VEE MIN -0.3 0 MAX 6.5 27 UNIT V V Note 1 NOTE Power Supply for Logic VDD-VSS
LCM should be grounded during handling LCM.
(2)ENVIRONMENTAL ABSOLUTE MAXIMUM RATINGS NORMAL TEMP. ITEM Ambient Temperature Humidity (without Condensation) Note 2 0 Note 2,4 OPERATING MIN MAX 50 STORAGE MIN -20 Note 3,5 MAX 70
Note 3 Note 4 Note 5
Ta50C:85%RH max Ta50C:Absolute humidity must be lower than the humidity of 85%RH at 50C Ta at -20C will be < 48hrs at 70C will be < 120hrs Background color changes slightly depending on ambient temperature. This phenomenon is reversible. Ta70C:75RH max Ta>70C:absolute humidity must be lower than the humidity of 75%RH at 70C
Date : 2006/9/7
AMPIRE CO., LTD.
2
3. ELECTRICAL SPECIFICATION (Condition : Ta=25C)
Item Supply Voltage Input Voltage (Data,SCP,LP,FP) Power Supply Current for LCM (Typical case) Power Supply Current for CCFL B.L. VEE VIH VIL IDD IEE ICCFL Symbol VDD Conditions VDD=5V VDD=5.0V VEE-VDD=22.5V FLM=70Hz Vin=10.4V (TDK) CXA-L10L Specifications Unit min typ max 3.0 3.3 3.6 V 4.75 5.0 5.25 21 22.5 24 0.8 VDD VDD V Vss 0.2VDD 3.0 15 5 6.0 mA 30 mA
Note(3) : Life time of backlight will change according to the FL input current. Note(4) : FL Starting Voltage should be 1400 Vo-p min..
4.
CCFL B/L ELECTRICAL SPECIFICATION
Item Lamp Voltage Lamp Current Lamp Power consumption Lamp Frequency Lamp Life time Symbol VL IL PL FL LL At IL = 5mArms (note 2) Conditions VL=350Vrms (note 1)
(Condition : Ta=25C)
Specifications Unit min typ max -350 -Vrms 4 5 6 mArms -10000 1.75 35 ---W KHz hrs
(Note 1) Power consumption exclude inverter loss (Note 2) Lamp life time : The final brightness is at 50% of original brightness.
Date : 2006/9/7
AMPIRE CO., LTD.
3
4. MECHANICAL SPECIFICATION
(1)Product No. (2)Module Size (3)Dot Size (4)Dot Pitch (5)Number of Dots (6)Duty (7)Bias STN: FSTN: (8)LCD Display Mode Rear Polarizer : (9)Viewing Direction (10)Backlight (11)Controller (12)DC/DC Converter (13)Data connector (14)CCFL connector (15)Inverter (16)Weight AG-640480C1FTCW 205.5(W)x x7.0 max(D) 0.21(W)mm x 0.21(H)mm 0.23(W)mm x0.23(H)mm 640(W) x 480(H)Dots 1/240 Dual Scan 1/13 Gray Mode Yellow Mode Blue Mode Black and White (Normally White/Positive Image) Black and White (Normally Black/Negative Image) Reflective Transflective Transmissive Transflective(High Transmissive) 6 O'clock W/O 12 O'clock WTA-M10L (310) g 3 O'clock CCFL EL LED
Date : 2006/9/7
AMPIRE CO., LTD.
4
5. OPTICAL SPECIFICATIONS
ITEM Contrast SYMBOL CONDITION MIN. K 7.0 25C 440 0C Tr 180 25C 90 50C 200 0C Tf 90 25C 75 50C f b 25C r l Fr 25C x 25C y 25C Vin=10.4V IL=5mA 70.0 L (TDK) CXA-L10L All dots ON All dots OFF -TYP. 10.0 550 234 110 250 110 95 50 26 45 45 70 0.31 0.34 MAX. UNIT NOTE 6 820 350 ms 165 7 375 165 140 Degree 8 Hz 9 85.5 cd/m
2
Response Time
Viewing angle range Frame frequency Colour
Luminance
13.3
20.0
cd/m2
Date : 2006/9/7
AMPIRE CO., LTD.
5
[Note 6 ] Definition of Operation Voltage (VEE)
Intensity 100H Selected Wave Non-selected Wave Intensity 100H
Non-selected Wave Selected Wave
Cr Max Cr = Lon / Loff
Cr Max Cr = Lon / Loff
Vop
Driving Voltage(V)
Vop
Driving Voltage(V)
[positive type]
[Negative type]
[Note 7 ] Definition of Response Time ( Tr , Tf )
Non-selected Conition Intensity 10H 90H Selected Conition Non-selected Conition
Non-selected Conition Intensity
Selected Conition
Non-selected Conition
100H
100H
90H 10H
Tr
Tf
Tr
Tf
[positive type]
[Negative type]
Conditions : Operating Voltage : VLCD Frame Frequency : 64 HZ
Viewing Angle( , O) : 0, 0 Driving Waveform : 1/N duty , 1/a bias [Note 9 ] Definition of measuring points
1/4 W 1/4 W 1/4 W 1/4 W
[Note 8 ] Definition of viewing angle(CR2)
1/4 H
1
1/4 H
2 5 8
3 6 9 H
4
1/4 H
7
1/4 H
w
Date : 2006/9/7
AMPIRE CO., LTD.
6
6. INTERFACES
6.1 Interface Pin Assignment LCD Connector : MOLEX 53261-1590 Pin No. Signal Function Frame Pulse Scan start-up signal 1 FLM 2 CL1(LP ) Latch Pulse in one line 3 CL2(SCP) Shift Clock Pulse for X-Drivers Sequence Signal of Power Supply("L":OFF) 4 /DISP Power Supply for Logic(+5V) 5 VDD Ground(0 V) 6 VSS Power Supply for Contrast Control 7 VEE Data Input for Upper Screen 8 UD0 Data Input for Upper Screen 9 UD1 Data Input for Upper Screen 10 UD2 Data Input for Upper Screen 11 UD3 Data Input for Lower Screen 12 LD0 Data Input for Lower Screen 13 LD1 Data Input for Lower Screen 14 LD2 Data Input for Lower Screen 15 LD3 Mating Connector : MOLEX 51021-1500 (HOUSING) x 1 + MOLEX 50058-8000(TERMINAL) x 15 6.2 CCFL B/L Pin Assignment FL Connector MITSUMI : M63-M83-04 Pin No. Signal Function Power Supply for FL(Hot) High Voltage Line 1 HV No Connection 2 NC No Connection 3 NC Power Supply for FL(Ground) Ground Line 4 GND Mating Connector : MITSUMI : M63M83 M60-04-30-114P(MITSUMI) M60-04-30-134P(MITSUMI) M61M73-04(MITSUMI)
Date : 2006/9/7
AMPIRE CO., LTD.
7
7. BLOCK DIAGRAM
UD0~UD3 LD0~LD3 1 2 3 4 5 6 7 8
FLM CL1 (LP) CL2(SCP) /DISP CL1,CL2
CL1
AC Signal Generator
M
M, /DISP SEG Drivers (Upper)
VDD VSS VEE UD0 i 11 UD3 12 LD0 i 13 LD3
COM Drivers
FLM,CL1 M, DISP
640N 480 LCD PANEL SEG Drivers (Lower)
Bias Circuit Generator
1 2 3 4 HV NC NC GND
CCFL Back-Light
Date : 2006/9/7
AMPIRE CO., LTD.
8
8. POWER SUPPLY
LCM
VDD VSS
5V
R1 R2 R3
+27V
PCB
VEE VH GND R1I R2I
Recommendation Circuit
CCFL B/L
R3x 10~20K[
Date : 2006/9/7
AMPIRE CO., LTD.
9
9. TIMING CHARACTERISTICS
9-1. Interface timing:
Date : 2006/9/7
AMPIRE CO., LTD.
10
10. DISPLAY PATTERN
4 BITS INPUT
UD3 UD2 UD1 UD0
1,1 1,2 1,3 1,4 KKKKKKKKKKKKKKKKKKKKK 2,1 2,2 2,3 2,4 KKKKKKKKKKKKKKKKKKKKK
1,159 1,160 2,159 2,160
480 Lines
240,1 241,1
240,160 241,160
479,1 479,2 KKKKKKKKKKKKKKKKKKKKK 480,1 480,2 KKKKKKKKKKKKKKKKKKKKK
479,159 479,160 480,159 480,160
LD3 LD2 LD1 LD0
640 Pixels
Date : 2006/9/7
AMPIRE CO., LTD.
11
11. RELIABILITY TEST
No 1 2 3 4 5 ITEM HIGH TEMP. Operation HIGH TEMP. Storage LOW TEMP. Operation LOW TEMP. Storage HIGH TEMP/HUMID Storage Conditions 50C 70C 0C -20C 50C 90% RH -20C,30 min 60C,30 min 70G , 11ms Dir-x , y , z 120 HR 120 HR 120 HR 120 HR 120 HR Note
6 7
THERMAL SHOCK SHOCK
10 cycle 3 time/dir
Definitions of life end point (1) Current consumption is more than specified value (2) Function of the module is not maintained (3) There is visible degradation of appearance and display quality (4) Contrast ratio is less than 50 % of specified value (5) Brightness is less than 50 % of specified minimum valued
12. APPEARANCE CHECK
CONDITION OF APPEARANCE CHECK : (1) Specimen shall be checked by eyes in distance of 30cm under 40w fluorescence lamp. (2) Checking direction shall be in 45 degree from perpendicular line of specimen surface.
viewing area display area
Date : 2006/9/7
AMPIRE CO., LTD.
12
13. HANDLING PRECAUTIONS
(1)Treat polarizer very carefully since it is easy to be damaged. (2)When cleaning the display surface, use soft cloth (e.g. wiper) with a solvent (recommended below)and wipe lightly. ethyl alcohol iso-propanol Do not wipe the display surface with dry or hard materials that will damage the polarizer surface. Do not use the following solvents : water ketone aromatics (3)Direct current causes electro-chemical reaction with remarkable degradation of the display quality. Give careful consideration to prevent direct current at ON/OFF timing and during operation. (4)Avoid strong shock and drop from a height. (5)To prevent LCD panels from degradation, do not operate or store them exposed directly to sunshine or high temperature/humidity. (6)Give careful consideration to avoid electrical static discharge with causes uneven contrast. (7)Even a small condensation on the contact pads (terminals) causes electro-chemical reaction which makes missing row and column. Give careful attention to avoid condensation. When assembling with zebra connector, clean the surface of the pads with alcohol and keep the air very clean.
Date : 2006/9/7
AMPIRE CO., LTD.
13
14. LCD PRODUCT QUALITY STANDARD
(1) SAMPLING : MIL-STD-105E SerialA AQL = 0.65(Major defect), 1.0(Minor defect) (2)DISPLAY APPEARANCE
NO ITEM 1. INCLUSIONS (BLACK SPOT, WHITE SPOT , DUST) CRITERIA (1)ROUND TYPE DIAMETER mm(a*) a 0.20 0.20 < a 0.35 0.35 < a (2)LINEAR TYPE LENGTH mm(L) NA 1L3 33. DENT 4. BUBBLE 5. PIN HOLE
1.SCRATCH ON PROTECTIVE FILM IS PERMITTED 2.SCRATCH ON POLARIZER SHALL BE AS FOLLOW: (1)ROUND TYPE DIAMETER mm(a*) NO. OF DEFECT a 0.15 NEGLECT 0.15 < a 0.20 2 MAX 0.20 < a NONE (2) LINEAR TYPE BE JUDGED BYE 1.-(2)LINEAR TYPE DIAMETER < 1.5mm NOT EXCEEDING 0.5mm AVERAGE DIAMETER IS ACCEPTABLE BETWEEN GLASS AND POLARIZING FILM. (a+b)/2 0.15mm MAXIMUM NUMBER:IGNORED 0.15 < (a+b)/2 0.20mm MAXIMUM NUMBER:10
Minor Minor Minor
6. DOT DEFECT
(a+b)/2 0.20mm MAXIMUM NUMBER:IGNORED 0.20 < (a+b)/2 0.30mm MAXIMUM NUMBER:5 X=WIDTH
Minor
7. CONTRAST IRREGULARITY(S POT)
Minor DIAMETER SPEC A 0.50mm 0.50 < a 0.75 0.75 < a 1.00 1.00< a NO. OF DEFECT NEGLECT 5 3 NONE Minor Minor
8. DOT WIDTH DESIGN WIDTHO 15% 9. COLOR TONE AND OBVIOUS UNEVEN COLOR IS NOT PERMITTED UNIFORMITY
15. OUTLINE DIMENSIONS
Date : 2006/9/7 AMPIRE CO., LTD.
14
Cabl eo 250. 0 t o 200. 0m m
Date : 2006/9/7
o u q i
AMPIRE CO., LTD.
15

▲Up To Search▲

Price & Availability of AG-640480C2FTCW

	To Download AG-640480C2FTCW Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .